Sn-358 plus manual

Note: A bamboo pole is preferred. If a metal one is used, be sure it is isolated. Put up the pole and make a loop with the cable cord. The loop which is 15cm in diameter to prevent water from going down into the base unit as figure 5.

The assembled outdoor antenna as indicated in Figure 6. Page: 14 Notes: 1. Make sure that the cable is tied to the cable connector in order to maintain the radio frequency transmission performance. The ground plane should be at least 3 meters above the ground.

Straighten the remaining cable. Bending cable cord will increase loss of transmission power. Make a loop before pulling the cable into the house. The loop can prevent rain from going into the house. The higher the antenna is installed the better the communication will be. Page: 15 Basic Operation for Base A. Call function 1. Making calls Press first and then dial the number after hearing the dial tone. For example, dial the phone number Redial While in standby mode, press first, then press Redial.

Automatic Dialing 1. If the base unit is connected to a PBX. This can prevents miss dialing when you redial or dial a stored number. Dialing a stored number in standby mode Auto dial the phone number stored in location " N ". Page: 16 4. Answering Calls Press to answer a call. To hang up, press again. Paging the target handset from the base unit 1.

To stop paging, press again. To accept a page, press any key except or remove from the charger if handset is docked. To end the intercom, press key or place the handset back onto the Charger.

NOTE: Once paging from the base unit, a confirmed melody will sounds if the base unit receives the response from the handset. If the melody does not sound, it means that: 1 The handset is off. Intercom during a call While you are using the base unit to make or answer an incoming call, there are 2 methods to page the handset and still keep your current telephone call.

If you want to talk to any handset, simply press the key only. It will put the current telephone line on hold, play the hold music to the line, and the base unit will begin paging all handsets. Any handset can answer the page. Only the handset with the unique ID number N N will be paged.

During handset and base unit conversation, either the base unit or the handset can resume conversation with the call on hold by pressing on the base unit, or on the handset. Transfer a phone While you are using the base unit to make or answer an incoming call, there are two methods to transfer the call over to other handsets. If there is no answer from the target handset, you will hear feedback tones to alert you to receive the call on hold again. Setting 1. There are 8 steps can be selected.

The lowest level is mute. There are 7 steps can be selected. Flash time setting. Page: 18 5. Register new handset 7. Set Tone dialing Page: 19 Pressing the key will place the current call on hold, and pick up the incoming call.

Pressing the key again will return you to the first call and place the second call on hold. Intercom: 1. Paging the base from the handset: Press the key on the handset and then press BASE left soft key to establish intercom. You can power on the handset on by pressing and holding for 3 seconds. You can power off the handset off by pressing and holding for 3 seconds. Making a Telephone Call: You can make an outgoing call in one of two ways. Press , wait for dial tone, and then enter phone number.

Enter phone number first then press. Answering incoming Calls: On incoming calls, the ringer will ring or vibrate unless the ringer has been turned off. If the handset is on charger cradle, lift the handset to pick up the incoming call.

If the handset is not on charger cradle, press any key to answer the incoming call except. If you do not take the incoming calls, the display will prompt you on how many calls you have missed. Note: While receiving incoming calls, you can mute the ring by pressing key. Disconnecting calls: You can end a call by pressing or by placing the handset onto the charger cradle. Redial: 1. You can use the Up Arrow Key to scroll through the last 10 phone numbers dialed.

Select and press. Page: 20 in microphone. Paging the handset from another handset: This has to be done through the walkie-talkie mode. Please refer to the section. Walkie-Talkie Between Handsets. Walkie-Talkie between handsets: 1. Press the key followed by the 2 digit unique handset ID to establish contact.

You can press button to talk, then release it to listen. Note: To end calls, please keep pressing button for more than 2 sec. Cigarette adaptor The cigarette adaptor ensures your phone is ready for use wherever you travel.

This small charge's functional design fits most car lights and interiors. The charging time is about 4 hours, and you can use your phone freely during charging. A green light indicates that is ready for charging. The input voltage can be 12 or 24 V DC, negative grounding. Avoid prolonged charging when the car engine is not running; this may cause the battery of your car to drain. Note also that in some cares the cigarette lighter plug is not provided with electricity if the ignition is switched off.

Verify that green LED light is on. Ear Phone Jack Setup Menu This jack is used for connecting ear-microphone and cigarette adaptor to handset. Please connect them like the figure below.

Battery Charge The handset can be charged on the base unit or the charger. The green LED indicator on handset will turn on. Please make sure put the twin charger away from the base unit farther than 30 cm.

Outdoor Antenna Installation of the outdoor antenna is very important for communication range and quality. Be sure to follow the following steps. A large number of your handset's options are accessed by using smart switch which is specially designed to allow you operate this handset with one thumb only.

The access uses a common approach for selection, change and cancellation. Please read this section carefully before attempting to access smart switch. When you understand the common approach to menu navigation and how the options are shown, you will be able to access and change options with ease.

The menu described here can be started accessing when the handset is in the standby mode. Use the wrench to screw the antenna tightly. Lock the 6 ground planes with the base part as illustrated in Figure 2. NOTE: Long and short ground planes should be alternately arranged.

Entering the Menus Figure 1 You can either scroll or press smart switch to access the menu. Once enter the menu, you can use smart switch to access and select options. Menus and Sub-menus A menu is a simple list of options.

Some of options provide access to a further list of options called a sub-menu. When navigation through the menus you may find it helpful to think in terms of menu levels-the "present" menu being on one level and its sub-menus being on a lower level.

Moving to and selecting a Menu Option Ground planes x 3 Ground planes x 3 To move from one option to another on the same level, use smart switch to scroll upwards or downwards. When you find the option you want, press smart switch to select it. Depending on the option you select, one of two things will happen: either a brief message will be displayed confirming an action, for example OK or the first and second option of a sub-menu will be displayed.

You can select this option pressing smart switch or browse through the other options by scrolling the smart switch. Figure 2 14 23 L. Changing Channel: During a call in progress, you can press FUN then to change radio channel to avoid interference.

Automatic Dialing 1. The saved memory will be replaced if two approaches are accessed to the same location. This can prevents miss dialing when you redial or dial a stored number.

Assemble cable jack with the base part as illustrated in Figure 3. NOTE: A bamboo pole is preferred. If a metal one is used, be sure it is isolated. Put up the pole and make a loop with the cable cord. The loop which is 15 cm in diameter to prevent water from going down into the base unit as figure 5. Ground planes Screw Washer 6. The assembled outdoor antenna as indicated in Figure 6. Pole N. Tape Figure 5 Figure 6 22 Cable cord connector 15 F. Redial: NOTES: 1 Make sure that the cable is tied to the cable connector in order to maintain the radio frequency transmission performance.

The loop can prevent rain from going into the house. Don't install the antenna in the rain to avoid thunder striking. Intercom: 1. Paging the base from handset a. Base: When the other party's voice is heard, answer through the microphone.

Paging the handset from base a. During a call in progress, the call will be on hold. You can continuously press smart switch to talk and release it to listen To. During the conference proceeding, the multi-Talk indicator of base Unit will be turned on. When in the TALK mode, scrolling up or down the smart switch can adjust the volume from 6 different levels.

Call function A. When the handset is under power-off, you can press END key to turn it on. When the handset is in the standby mode, you can press END key to turn it off. Making Calls: You can make an outgoing call in one of two ways. When the dial tone is heard, you can dial a number and the screen will display the number being dialed. Answering Calls: 1.

If the handset is in the base or charger, pick up the handset to answer the call. Otherwise, press any key except END key to take the incoming call.

You can refer to the option of ReceivedCalls for looking over its content. END A Redial Redial While in standby mode, press first, then press Redial. Hands-free Speaker Phone: Once press the button on the right-upper corner of handset to enter this function. Co-production practitioners network. Find great deals on eBay for senao Shop with confidence. Skip to main content. Brand New. Senao SR If the above display content still appears, please re-register handset G. Intercom 3.

Walkie-Talkie between handsets Voice Volume K. Changing Channel Walkie-Talkie M. Multi-handset system up to Voice Volume Walkie-talkie between handsets. Walkie-Talkie Base speakerphone with dial keypad. Base Unit 2 ReceivedCalls This option is used to display the information of received calls max 30 calls including name and phone number.

When selected, LCD screen on handset will display the number of new call not been accessed and the Antenna total numbers of received calls. Page 8: Handset B. Handset Erase One Status indicator When selected, the current record of outgoing phone call will be Green: in use deleted.

Page 9 Memo Menu Signal strength: The more segments displayed in the bar graph, the better the signal strength. Page Installation Date Setting When selected, you can check or set the date stored in the handset and base.